OkBike Logo
OkBike Logo
Home Verified Garages Serviceable Pincodes Hotspots Demand Partner (Mechanic Portal)
Book Doorstep Service Get on Google Play

Choose Your City

Explore verified bike garages & doorstep service across India

Language:

Fault Code P0123 Diagnostic Solution

Step-by-step diagnostic checks, multimeter testing values, wiring inspections & OBD-II erase guides for BS6 two-wheelers.

OkBike App Icon

OkBike Mechanic App

Live sensor graphs, 1,000+ color wiring diagrams, ECU pinouts & OBD-II scanner.

P0123
Fuel & Air Metering
Standard OBD-II Diagnostic Protocol
Share with Mechanic
Fault Description & Technical Meaning:

Throttle/Pedal Position Sensor/Switch A Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.

Diagnostic Summary: Diagnostic code P0123 triggers due to a circuit high affecting the Throttle Position Sensor (TPS), impacting proper vehicle operation.

Related Components (Photo & Inspection)

3 Components (Tap to Zoom)
EOT Sensor (Engine Oil Temperature)
Sensor

EOT Sensor (Engine Oil Temperature)

Click to inspect photo & test specs

Throttle Position Sensor (TPS)
Sensor

Throttle Position Sensor (TPS)

Click to inspect photo & test specs

12V Motorcycle Battery
Electrical

12V Motorcycle Battery

Click to inspect photo & test specs

Common Symptoms
  • • Check Engine Light (MIL Lamp): Illuminates or flashes on the speedometer console.
  • • Engine Hesitation & Jerking: Poor throttle response during sudden acceleration.
  • • Drop in Fuel Economy: Open-loop fuel spraying increases petrol consumption and causes black smoke.
  • • Hard Cold Starting: Engine dies during idle or requires multiple starter button attempts.
Common Root Causes
  • • Wiring Harness Damage: Chafed wires touching motorcycle frame metal or rodent cuts.
  • • Loose / Corroded Coupler: Green oxidation or loose push-fit pins inside connector plug.
  • • Defective Component: Burnt internal sensing thermistor or solenoid actuator coil.
  • • Low Battery Voltage: Weak motorcycle battery under 12.0V causing ECU reference error.

Step-by-Step Diagnostic & Repair Procedure

Bench-tested repair procedure for code P0123

5 Steps
Step 1: Turn off the vehicle ignition switch, remove the key, and allow all electrical and mechanical systems to cool down completely. Locate the Throttle Position Sensor (TPS), typically positioned fastened securely to the side of the throttle body on the throttle shaft pivot.
Step 2: Carefully unplug the electrical wiring coupler from the Throttle Position Sensor (TPS). Inspect the connector pins and socket terminals for green copper corrosion, water moisture, bent pins, or melted plastic. Trace the wiring harness back toward the control module and check for chafing, wire cuts, or melted insulation touching vehicle metal.
Step 3: Set a digital multimeter to DC Volts and turn the ignition key ON without starting the engine. Check for proper electrical reference voltage (5.0V reference or 12V battery power depending on component specification). Next, set the meter to Ohms (continuity) and check for an accidental short-circuit to 12V battery power and test the ground circuit wire to ensure resistance to ground is under 0.5 Ohms to ensure the ground circuit has less than 0.5 Ohms resistance to the chassis ground.
Step 4: Bench-test the component by measuring its internal resistance across the electrical terminals using your multimeter (5.0V reference voltage, clean ground, and signal voltage sweeping smoothly from approx 0.6V at idle to 4.5V at wide open throttle without dead spots). If the component is carbon-fouled, contaminated, or has poor pin tension, clean it carefully using dedicated electrical contact cleaner. If the internal coil or sensor circuit shows zero Ohms (short) or infinite Ohms (open), replace the component with a genuine OEM part.
Step 5: Reconnect the electrical coupler firmly until the locking tab audibly clicks into place. Connect an OBD-II diagnostic scanner or use the OkBike Mechanic App to erase stored DTC fault memory from the ECU. Start the engine or power up the vehicle, perform a test drive covering varied speeds, and verify that the Warning Light remains permanently turned off.
Important Note: Simply replacing the sensor does not immediately clear the Check Engine Light (MIL). Connect an OBD-II scanner to the motorcycle diagnostic connector and execute "Erase Stored DTC Memory" followed by a road test.

Related Diagnostic Fault Codes

P0120 Throttle/Pedal Position Sensor/Switch A Circuit. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0121 Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance. This diagnostic trouble code indicates an in-range rationality fault where the sensor is sending a signal, but the value contradicts other sensor readings or expected physical limits. The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0122 Throttle/Pedal Position Sensor/Switch A Circuit Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0124 Throttle/Pedal Position Sensor/Switch A Circuit Intermittent. This diagnostic trouble code indicates intermittent signal dropouts or electrical noise caused by loose pin tension, vibration-induced wiring chafing, or cracked solder joints. The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Engine Coolant Temperature (ECT) Sensor measures engine cooling fluid temperature to regulate cold-start fuel enrichment, ignition timing advance, and radiator cooling fan switching. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0126 Insufficient Coolant Temperature for Stable Operation. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Engine Coolant Temperature (ECT) Sensor measures engine cooling fluid temperature to regulate cold-start fuel enrichment, ignition timing advance, and radiator cooling fan switching. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.