OkBike Logo
OkBike Logo
Home Verified Garages Serviceable Pincodes Hotspots Demand Partner (Mechanic Portal)
Book Doorstep Service Get on Google Play

Choose Your City

Explore verified bike garages & doorstep service across India

Language:

Fault Code P07C5 Diagnostic Solution

Step-by-step diagnostic checks, multimeter testing values, wiring inspections & OBD-II erase guides for BS6 two-wheelers.

OkBike App Icon

OkBike Mechanic App

Live sensor graphs, 1,000+ color wiring diagrams, ECU pinouts & OBD-II scanner.

P07C5
Transmission & Gear System
Standard OBD-II Diagnostic Protocol
Share with Mechanic
Fault Description & Technical Meaning:

Intermediate Shaft Speed Sensor A Circuit Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.

Diagnostic Summary: Diagnostic code P07C5 triggers due to a circuit low affecting the Vehicle Speed Sensor (VSS), impacting proper vehicle operation.

Related Components (Photo & Inspection)

5 Components (Tap to Zoom)
EOT Sensor (Engine Oil Temperature)
Sensor

EOT Sensor (Engine Oil Temperature)

Click to inspect photo & test specs

IAT Sensor (Intake Air Temperature)
Sensor

IAT Sensor (Intake Air Temperature)

Click to inspect photo & test specs

Vehicle Speed Sensor (VSS)
Sensor

Vehicle Speed Sensor (VSS)

Click to inspect photo & test specs

Idle Air Control Valve (ISC/IACV)
Actuator

Idle Air Control Valve (ISC/IACV)

Click to inspect photo & test specs

12V Motorcycle Battery
Electrical

12V Motorcycle Battery

Click to inspect photo & test specs

Common Symptoms
  • • Check Engine Light (MIL Lamp): Illuminates or flashes on the speedometer console.
  • • Engine Hesitation & Jerking: Poor throttle response during sudden acceleration.
  • • Drop in Fuel Economy: Open-loop fuel spraying increases petrol consumption and causes black smoke.
  • • Hard Cold Starting: Engine dies during idle or requires multiple starter button attempts.
Common Root Causes
  • • Wiring Harness Damage: Chafed wires touching motorcycle frame metal or rodent cuts.
  • • Loose / Corroded Coupler: Green oxidation or loose push-fit pins inside connector plug.
  • • Defective Component: Burnt internal sensing thermistor or solenoid actuator coil.
  • • Low Battery Voltage: Weak motorcycle battery under 12.0V causing ECU reference error.

Step-by-Step Diagnostic & Repair Procedure

Bench-tested repair procedure for code P07C5

5 Steps
Step 1: Turn off the vehicle ignition switch, remove the key, and allow all electrical and mechanical systems to cool down completely. Locate the Vehicle Speed Sensor (VSS), typically positioned mounted on the transmission output shaft, front wheel fork, or rear wheel brake disc assembly.
Step 2: Carefully unplug the electrical wiring coupler from the Vehicle Speed Sensor (VSS). Inspect the connector pins and socket terminals for green copper corrosion, water moisture, bent pins, or melted plastic. Trace the wiring harness back toward the control module and check for chafing, wire cuts, or melted insulation touching vehicle metal.
Step 3: Set a digital multimeter to DC Volts and turn the ignition key ON without starting the engine. Check for proper electrical reference voltage (5.0V reference or 12V battery power depending on component specification). Next, set the meter to Ohms (continuity) and check if the signal wire is shorted to the metal frame (0 Ohms to ground) and verify that the reference voltage is reaching the connector to ensure the ground circuit has less than 0.5 Ohms resistance to the chassis ground.
Step 4: Bench-test the component by measuring its internal resistance across the electrical terminals using your multimeter (12V/5V supply voltage, clean ground, and pulsing square-wave voltage (0V to 5V) when rotating the wheel). If the component is carbon-fouled, contaminated, or has poor pin tension, clean it carefully using dedicated electrical contact cleaner. If the internal coil or sensor circuit shows zero Ohms (short) or infinite Ohms (open), replace the component with a genuine OEM part.
Step 5: Reconnect the electrical coupler firmly until the locking tab audibly clicks into place. Connect an OBD-II diagnostic scanner or use the OkBike Mechanic App to erase stored DTC fault memory from the ECU. Start the engine or power up the vehicle, perform a test drive covering varied speeds, and verify that the Warning Light remains permanently turned off.
Important Note: Simply replacing the sensor does not immediately clear the Check Engine Light (MIL). Connect an OBD-II scanner to the motorcycle diagnostic connector and execute "Erase Stored DTC Memory" followed by a road test.

Related Diagnostic Fault Codes

P07C2 Input/Turbine Shaft Speed Sensor B Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P07C3 Input/Turbine Shaft Speed Sensor C Circuit Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P07C4 Input/Turbine Shaft Speed Sensor C Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P07C6 Intermediate Shaft Speed Sensor A Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P07C7 Intermediate Shaft Speed Sensor B Circuit Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P07C8 Intermediate Shaft Speed Sensor B Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Vehicle Speed Sensor (VSS) generates vehicle speed pulses for the digital speedometer and ECU fuel cut / ABS speed monitoring. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.